UNT Libraries Government Documents Department - 14,538 Matching Results

Search Results

Results: 1 - 24 next
open access

1/m<sub>c</sub> Terms in lambda<sup>+</sup><sub>c</sub> Semileptonic Decays

Description: We use the heavy quark effective theory to investigate the form factors that describe the semileptonic decays lambda<sup>+</sup><sub>c</sub> -> lambda e<sup>+</sup> nu, to order 1/m<sub>c</sub>. We find that a total of four form factors are needed to this order, in contrast with two form factors to leading order, and six form factors in the most general case. We point out some relationships that arise among the general form factors.
Date: February 1, 1992
Creator: Roberts, Winston
Item Type: Refine your search to only Article
open access

A 2 to 4 nm high power FEL on the SLAC linac

Description: We report the results of preliminary studies of a 2 to 4 nm SASE FEL, using a photoinjector to produce the electron beam, and the SLAC linac to accelerate it to an energy up to 10 GeV. Longitudinal bunch compression is used to increases ten fold the peak current to 2.5 kA, while reducing the bunch length to the subpicosecond range. The saturated output power is in the multi-gigawatt range, producing about 10{sup 14} coherent photons within a bandwidth of about 0.2% rms, in a pulse of several mi… more
Date: September 1, 1992
Creator: Pellegrini, C.; Rosenzweig, J.; Nuhn, H. D.; Pianetta, P.; Tatchyn, R.; Winick, H. et al.
Item Type: Refine your search to only Article
open access

3-D Field Computations for Accelerator Magnets Using Finite Element and Integral Codes

Description: Two dimensional (2-D) computation has been an accepted part of the design of accelerator magnets since the 1960's, but three-dimensional (3-D) computations are still not fully trusted. This paper describes the successes and limitations of 3-D computations, as applied to accelerator magnets for the Advanced Photon Source (APS) at Argonne National Laboratory (ANL). Both the finite element code TOSCA and the edge element volume integral code CORAL have been used in these computations. The ends of … more
Date: 1992~
Creator: Turner, L. R.; Kim, S. H.; Kim, K. & Kettunen, L.
Item Type: Refine your search to only Article
open access

3-D field computations for accelerator magnets using finite element and integral codes

Description: Two dimensional (2-D) computation has been an accepted part of the design of accelerator magnets since the 1960`s, but three-dimensional (3-D) computations are still not fully trusted. This paper describes the successes and limitations of 3-D computations, as applied to accelerator magnets for the Advanced Photon Source (APS) at Argonne National Laboratory (ANL). Both the finite element code TOSCA and the edge element volume integral code CORAL have been used in these computations. The ends of … more
Date: December 1, 1992
Creator: Turner, L. R.; Kim, S. H.; Kim, K. & Kettunen, L.
Item Type: Refine your search to only Article
open access

3-D numerical investigation of the mantle dynamics associated with the breakup of Pangea

Description: Three-dimensional finite element calculations in spherical geometry are performed to study the response of the mantle with platelike blocks at its surface to an initial condition corresponding to subduction along the margins of Pangea. The mantle is treated as an infinite Prandtl number Boussinesq fluid inside a spherical shell with isothermal, undeformable, free-slip boundaries. Nonsubducting rigid blocks to model continental lithosphere are included in the topmost layer of the computational m… more
Date: January 1, 1992
Creator: Baumgardner, J. R.
Item Type: Refine your search to only Article
open access

3-D numerical investigation of the mantle dynamics associated with the breakup of Pangea

Description: Three-dimensional finite element calculations in spherical geometry are performed to study the response of the mantle with platelike blocks at its surface to an initial condition corresponding to subduction along the margins of Pangea. The mantle is treated as an infinite Prandtl number Boussinesq fluid inside a spherical shell with isothermal, undeformable, free-slip boundaries. Nonsubducting rigid blocks to model continental lithosphere are included in the topmost layer of the computational m… more
Date: October 1, 1992
Creator: Baumgardner, J. R.
Item Type: Refine your search to only Article
open access

7-GeV Advanced Photon Source Instrumentation Initiative. Conceptual Design Report

Description: In this APS Instrumentation Initiative, 2.5-m-long and 5-m-long insertion-device x-ray sources will be built on 9 straight sections of the APS storage ring, and an additional 9 bending-magnet sources will also be put in use. The front ends for these 18 x-ray sources will be built to contain and safeguard access to these bright x-ray beams. In addition, funds will be provided to build state-of-the-art insertion-device beamlines to meet scientific and technological research demands well into the … more
Date: October 1992
Creator: Argonne National Laboratory
Item Type: Refine your search to only Report
open access

7-GeV Advanced Photon Source Instrumentation Initiative conceptual design report

Description: In this APS Instrumentation Initiative, 2.5-m-long and 5-m-long insertion-device x-ray sources will be built on 9 straight sections of the APS storage ring, and an additional 9 bending-magnet sources will also be put in use. The front ends for these 18 x-ray sources will be built to contain and safeguard access to these bright x-ray beams. In addition, funds will be provided to build state-of-the-art insertion-device beamlines to meet scientific and technological research demands well into the … more
Date: December 1992
Item Type: Refine your search to only Report
open access

7-GeV Advanced Photon Source Instrumentation Initiative conceptual design report

Description: In this APS Instrumentation Initiative, 2.5-m-long and 5-m-long insertion-device x-ray sources will be built on 9 straight sections of the APS storage ring, and an additional 9 bending-magnet sources will also be put in use. The front ends for these 18 x-ray sources will be built to contain and safeguard access to these bright x-ray beams. In addition, funds will be provided to build state-of-the-art insertion-device beamlines to meet scientific and technological research demands well into the … more
Date: December 1, 1992
Item Type: Refine your search to only Report
open access

9-{beta}-arabinofuranosyladenine preferentially sensitizes radioresistant squamous cell carcinoma cell lines to x-rays

Description: The effect of 9-{beta}-arabinofuranosyladenine (ara-A) on sensitivity to the deleterious effects of x-rays was studied in six squamous cell carcinoma cell lines. Three lines were relatively radioresistant, having D{sub 0} values of 2.31 to 2.89 Gy, and the other three lines were relatively radiosensitive, having D{sub 0} values of between 1.07 and 1.45 Gy. Ara-A (50 or 500 {mu}M) was added to cultures 30 min prior to irradiation and removed 30 min after irradiation, and sensitivity was measured… more
Date: June 1, 1992
Creator: Heaton, D.; Mustafi, R. & Schwartz, J. L.
Item Type: Refine your search to only Report
open access

The 17 keV neutrino and neutrino tagging

Description: P-788 at FNAL proposed to search for neutrino oscillations in a tagged neutrino line. A K{sub L} beam and the decay modes K{sub L} {yields} {pi}{mu}{nu}{sub {mu}} and K {sub L} {yields} {pi}e{nu}{sub e} provides the neutrino flux. An upstream tagging spectrometer then identifies the hadron and lepton and reconstructs the K{sub L} decay; the lepton identification will specifies the neutrino as {nu}{sub e} or {nu}{sub {mu}} and distinguishes {nu} from {bar {nu}} at the decay vertex. A neutrino de… more
Date: February 1, 1992
Creator: Bernstein, R.H.
Item Type: Refine your search to only Article
open access

The 17 keV neutrino and neutrino tagging

Description: P-788 at FNAL proposed to search for neutrino oscillations in a tagged neutrino line. A K{sub L} beam and the decay modes K{sub L} {yields} {pi}{mu}{nu}{sub {mu}} and K {sub L} {yields} {pi}e{nu}{sub e} provides the neutrino flux. An upstream tagging spectrometer then identifies the hadron and lepton and reconstructs the K{sub L} decay; the lepton identification will specifies the neutrino as {nu}{sub e} or {nu}{sub {mu}} and distinguishes {nu} from {bar {nu}} at the decay vertex. A neutrino de… more
Date: February 1, 1992
Creator: Bernstein, R. H.
Item Type: Refine your search to only Article
open access

A 50 mm bore superconducting dipole with a unique iron yoke structure

Description: A 50 mm bore superconducting dipole with a thin stainless steel collar and a close in elliptical iron yoke was designed in order to obtain a high transfer function SW low saturation effects on the multipoles, and a one meter model was built and tested. Training behavior of the first 1 m model, called D19, is presented at 4.3 K and 1.8 K. At 1.8 K it reached the record field of 10.06 T. The two layer cos [theta] winding uses 30 and 36 strand cables identical to the cables of the 50 mm bore SSC d… more
Date: August 1, 1992
Creator: Dell'Orco, D.; Caspi, S.; O'Neill, J.; Lietzke, A.; Scanlan, R.; Taylor, C. E. et al.
Item Type: Refine your search to only Article
open access

A 50 mm bore superconducting dipole with a unique iron yoke structure

Description: A 50 mm bore superconducting dipole with a thin stainless steel collar and a close in elliptical iron yoke was designed in order to obtain a high transfer function SW low saturation effects on the multipoles, and a one meter model was built and tested. Training behavior of the first 1 m model, called D19, is presented at 4.3 K and 1.8 K. At 1.8 K it reached the record field of 10.06 T. The two layer cos {theta} winding uses 30 and 36 strand cables identical to the cables of the 50 mm bore SSC d… more
Date: August 1, 1992
Creator: Dell`Orco, D.; Caspi, S.; O`Neill, J.; Lietzke, A.; Scanlan, R.; Taylor, C. E. et al.
Item Type: Refine your search to only Article
open access

100 MeV laser accelerator demonstration and 1 GeV baseline design development. 1992 Annual report

Description: The acceleration of relativistic electrons using the inverse Cerenkov effect was first demonstrated at Stanford University in 1981. Later, Fontana and Pantell developed an improved configuration for the inverse Cerenkov acceleration (ICA) process. A radially polarized laser beam is focused by an axicon onto the e-beam traveling through a gas-filled interaction region. The light intersects the e-beam at the Cerenkov angle {theta}{sub c}, where {theta}{sub c} = cos{sup {minus}1}(1/n{beta}), n is … more
Date: December 1, 1992
Item Type: Refine your search to only Report
open access

101-SY Hydrogen Safety Project chemical analysis support: Window ``C`` total organic carbon analysis

Description: Core samples taken from Hanford double-shell waste tank 101-SY during Window ``C`` (after the May 1991 gas release event) were analyzed for total organic carbon by the staff of the Analytical Chemistry Laboratory at Pacific Northwest Laboratory. The procedure uses the oxidation/extraction method of hot acid persulfate oxidation. Evolved CO{sub 2} is measured by a UIC Coulometric Carbon Analyzer coulometry detector. Samples are acidified with heated sulfuric acid to drive off all inorganic carbo… more
Date: January 1, 1992
Creator: Gillespie, B. M.; Stromatt, R. W.; Baldwin, D. L. & Hoopes, F. V.
Item Type: Refine your search to only Report
open access

101-SY Hydrogen Safety Project chemical analysis support: Window C'' total organic carbon analysis

Description: Core samples taken from Hanford double-shell waste tank 101-SY during Window C'' (after the May 1991 gas release event) were analyzed for total organic carbon by the staff of the Analytical Chemistry Laboratory at Pacific Northwest Laboratory. The procedure uses the oxidation/extraction method of hot acid persulfate oxidation. Evolved CO{sub 2} is measured by a UIC Coulometric Carbon Analyzer coulometry detector. Samples are acidified with heated sulfuric acid to drive off all inorganic carbona… more
Date: January 1, 1992
Creator: Gillespie, B. M.; Stromatt, R. W.; Baldwin, D. L. & Hoopes, F. V.
Item Type: Refine your search to only Report
open access

The 400 MeV Linac Upgrade at Fermilab

Description: The Fermilab Linac Upgrade in planned to increase the energy of the H[sup [minus]] linac from 200 to 400 MeV. This is intended to reduce the incoherent space-charge tuneshift at injection into the 8 GeV Booster which limit either the brightness or the total intensity of the beam. The Linac Upgrade will be achieved by replacing the last four 201.25 MHs drift-tube linac (DTL) tanks which accelerate the beam from 116 to 200 MeV, with seven 805 MRs side-coupled cavity modules operating at an averag… more
Date: December 1, 1992
Creator: Noble, R.J.
Item Type: Refine your search to only Article
open access

The 400 MeV Linac Upgrade at Fermilab

Description: The Fermilab Linac Upgrade in planned to increase the energy of the H{sup {minus}} linac from 200 to 400 MeV. This is intended to reduce the incoherent space-charge tuneshift at injection into the 8 GeV Booster which limit either the brightness or the total intensity of the beam. The Linac Upgrade will be achieved by replacing the last four 201.25 MHs drift-tube linac (DTL) tanks which accelerate the beam from 116 to 200 MeV, with seven 805 MRs side-coupled cavity modules operating at an averag… more
Date: December 1992
Creator: Noble, Robert J.
Item Type: Refine your search to only Article
open access

500 MW demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO[sub x]) emissions from coal-fired boilers

Description: The project provides a stepwise retrofit of an advanced overfire air (AOFA) system followed by low NO[sub x] burners (LNB). During each test phase of the project, diagnostic, performance, long-term, and verification testing will be performed. These tests are used to quantify the NO[sub x] reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulatecharacteristics and boiler efficiency. Baseline, AOFA, and LNB without AOFA test seg… more
Date: January 1, 1992
Item Type: Refine your search to only Report
open access

500 MW demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Third quarterly progress report, 1992: Innovative Clean Coal Technology (ICCT)

Description: The project provides a stepwise retrofit of an advanced overfire air (AOFA) system followed by low NO{sub x} burners (LNB). During each test phase of the project, diagnostic, performance, long-term, and verification testing will be performed. These tests are used to quantify the NO{sub x} reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulatecharacteristics and boiler efficiency. Baseline, AOFA, and LNB without AOFA test seg… more
Date: December 31, 1992
Item Type: Refine your search to only Report
open access

600 kV modulator design for the SLAC Next Linear Collider Test Accelerator

Description: Preliminary design for the SLAC Next Linear Collider Test Accelerator (NLCTA) requires a pulse power source to produce a 600 kV, 600 A, 1.4 {mu}s, 0.1% flat top pulse with rise and fall times of approximately 100 ns to power an X-Band klystron with a microperveance of 1.25 at {approx} 100 MW peak RF power. The design goals for the modulator, including those previously listed, are peak modulator pulse power of 340 MW operating at 120 Hz. A three-stage darlington pulse-forming network, which prod… more
Date: July 1, 1992
Creator: Harris, K.; de Lamare, J.; Nesterov, V. & Cassel, R.
Item Type: Refine your search to only Article
open access

600 kV modulator design for the SLAC Next Linear Collider Test Accelerator

Description: Preliminary design for the SLAC Next Linear Collider Test Accelerator (NLCTA) requires a pulse power source to produce a 600 kV, 600 A, 1.4 {mu}s, 0.1% flat top pulse with rise and fall times of approximately 100 ns to power an X-Band klystron with a microperveance of 1.25 at {approx} 100 MW peak RF power. The design goals for the modulator, including those previously listed, are peak modulator pulse power of 340 MW operating at 120 Hz. A three-stage darlington pulse-forming network, which prod… more
Date: July 1, 1992
Creator: Harris, K.; de Lamare, J.; Nesterov, V. & Cassel, R.
Item Type: Refine your search to only Article
Back to Top of Screen