UNT Libraries Government Documents Department - 781 Matching Results

Search Results

prev Results: 25 - 48 next
open access

Analysis of Experimental Investigations of the Planing Process of the Surface of Water

Description: Pressure distribution and spray measurements were carried out on rectangular flat and V-bottom planing surfaces. Lift, resistance, and center of pressure data are analyzed and it is shown how these values may be computed for the pure planing procees of a flat or V-bottom suface of arbitrary beam, load and speed, the method being illustrated with the aid of an example.
Date: March 1944
Creator: Sottorf, W.
Item Type: Refine your search to only Report
open access

Analysis of factors affecting net lift increment attainable with trailing-edge split flaps on tailless airplanes

Description: From Introduction: "The lift increments of different flap arrangements were determined by the method of reference 1 with a simple chord correction factor being applied. This procedure is somewhat similar in basic principles to the method of reference 2. The accuracy of the present method was determined by calculating by means of this method the lift and moment increments of flaps on 10 different finite wing-flap combinations for which wind-tunnel data were available."
Date: September 1944
Creator: Maggin, Bernard
Item Type: Refine your search to only Report
open access

Analysis of Square Shear Web Above Buckling Load

Description: "A solution of Von Karman's fundamental equations for plates with large deflections is presented for the case of a shear web divided into square panels by reinforcing struts. Numerical solutions are given for struts of infinite rigidity and for struts the weight of which is one-fourth the weight of the sheet. The results are compared with Wagner's diagonal tension theory as extended by Kuhn and by Langhaar. It is found that the diagonal tension theory as developed by Kuhn agrees best with the p… more
Date: July 1944
Creator: Levy, Samuel; Fienup, Kenneth L. & Woolley, Ruth M.
Item Type: Refine your search to only Report
open access

Analysis of Vertical-Tail Loads in Rolling Pull-Out Maneuvers

Description: Bulletin presenting an analysis of the vertical-tail loads to be expected as a result of abrupt aileron action in accelerated flight, as in rolls from turns or pull-outs, for example. Critical tail loads may occur in rolling pull-out maneuvers, particularly on airplanes with good ailerons and low directional stability.
Date: August 1944
Creator: Gilruth, Robert R.
Item Type: Refine your search to only Report
open access

An Analytical Investigation of the Effects of Elevator-Fabric Distortion on the Longitudinal Stability and Control of an Airplane

Description: From Summary: "The results of an analytical investigation to determine the qualitative effects of elevator-fabric distortion on the stick-force characteristics of an airplane are presented. These results indicate that serious alteration of intended stick-force characteristics can be produced by elevator-fabric distortion."
Date: May 1944
Creator: Mathews, Charles W.
Item Type: Refine your search to only Report
open access

Anthracite Mine Fires: Their Behavior and Control

Description: Report describing what a chemist is able to contribute as a member of a fire-fighting team dealing with fires in an anthracite mine. Details are specifically given regarding the oxidation of coal and the relationship between the temperature and composition of a mine-fire atmosphere.
Date: 1944
Creator: Scott, G. S.
Item Type: Refine your search to only Report
open access

Applicability of Similarity Principles to Structural Models

Description: "A systematic account is given in part I of the use of dimensional analysis in constructing similarity conditions for models and structures. The analysis covers large deflections, buckling, plastic behavior, and materials with nonlinear stress-strain characteristics, as well as the simpler structural problems" (p. 1).
Date: July 1944
Creator: Goodier, J. N. & Thomson, W. T.
Item Type: Refine your search to only Report
open access

Application of Spring Tabs to Elevator Controls

Description: Report presenting equations for calculating the stick-force characteristics obtained with a spring-tab type of elevator control. The main problems encountered in the design of the satisfactory elevator spring tab are to provide stick forces in the desired range, to maintain the force per g sufficiently constant throughout the speed range, to avoid undesirable "feel" of the control in ground handling, and to prevent flutter.
Date: October 1944
Creator: Phillips, William H.
Item Type: Refine your search to only Report
open access

Application of Spring Tabs to Elevator Controls

Description: Equations are presented for calculating the stick-force characteristics obtained with a spring-tab type of elevator control. The main problems encountered in the design of a satisfactory elevator spring tab are to provide stick forces in the desired range, to maintain the force per g sufficiently constant throughout the speed range, to avoid undesirable "feel" of the control in ground handling or in flight at low airspeeds, and to prevent flutter. Examples are presented to show the design featu… more
Date: November 24, 1944
Creator: Phillips, William H.
Item Type: Refine your search to only Report
open access

Artificial Aging of Riveted Joints Made in Alclad 24S-T Sheet Using A17S-T, 17S-T, and 24S-T Rivets

Description: Note presenting an investigation of the effect of artificial aging on the strengths of driven rivets of the alloys used commercially for rivets: specifically, A17S-T, 17S-T, and 24S-T. The change in shear strength for each type of rivet after being exposed to artificial aging treatment of 10 hours at 375 degrees Fahrenheit applied to the driven rivets is described.
Date: September 1944
Creator: Zamboky, A. N.
Item Type: Refine your search to only Report
open access

Artificial Running-in of Piston Rings

Description: Report presenting a consideration of the performance of sliding surfaces, such as piston rings, cylinders, journals, and bearings in aircraft engines with reference to the surface characteristics that they possess before and after running-in, prior to service operation. The phenomena accompanying the running-in process are analyzed.
Date: March 1944
Creator: Bobrowsky, A. R. & Machlin, E. S.
Item Type: Refine your search to only Report
open access

An Automatically Variable Control Linkage and Its Effect on the Lateral-Control Characteristics of a High-Speed Fighter Airplane

Description: Report discusses an analysis and preliminary design of a control linkage that varies automatically with dynamic pressure. The advantages of the device, including greater lateral control than a fixed control linkage without additional aerodynamic balance, are detailed. The effect of variable linkage on lateral-control characteristics is also described.
Date: May 1944
Creator: Gillis, Clarence L.
Item Type: Refine your search to only Report
open access

Axial Fatigue of 10 Airplane Wing-Beam Specimens by the Resonance Method

Description: Note presenting axial fatigue tests made by the resonance method on 10 specimens from airplane wing beams. The specimens contained several types of stress raiser, such as rivets, holes, fittings, splices, reinforcing plates, and so forth. The results show a greater fatigue stress concentration factor for the wing-beam specimens than for drilled coupons machined from the flanges or for parallel strip coupons containing idle rivets.
Date: December 1944
Creator: Brueggeman, W. C.; Krupen, P. & Roop, F. C.
Item Type: Refine your search to only Report
open access

Axial Fatigue Tests at Zero Mean Stress of 24S-T Aluminum-Alloy Sheet With and Without a Circular Hole

Description: "Axial fatigue tests were made on 189 coupon specimens of 0.032-inch 24S-T aluminum-alloy sheet and a few supplementary specimens of 0.004-inch sheet. The mean load was zero. The specimens were restrained against lateral buckling by lubricated solid guides described in a previous report on this project. About two-thirds of the 0.032-inch specimens were plain coupons nominally free from stress raisers. The remainder contained a 0.1285-inch drilled hole at the center where the reduced section was… more
Date: November 1944
Creator: Brueggeman, W. C.; Mayer, M., Jr. & Smith, W. H.
Item Type: Refine your search to only Report
Back to Top of Screen