116 Matching Results

Search Results

prev Results: 25 - 48 next
open access

Comparison of Structural Efficiencies of Diagonal-Tension Webs and Truss Webs of 24S-T Aluminum Alloy

Description: "A comparison is made of the structural efficiencies of truss webs of 24S-T aluminum alloy with previously published values of the structural efficiencies of diagonal-tension webs of 24S-T aluminum alloy on the basis of identical allowable stresses. It is concluded that the diagonal-tension beam (web and flanges) can usually be built to be a more efficient beam than the truss beam, even though over a small range the web of a Warren truss beam is slightly more efficient than the web of a diagona… more
Date: July 1945
Creator: Ochiltree, David W.
Partner: UNT Libraries Government Documents Department
open access

Effect of Variation in Diameter and Pitch of Rivets on Compressive Strength of Panels With Z-Section Stiffeners 1 - Panels With Close Stiffener Spacing That Fail by Local Buckling

Description: An experimental investigation is being conducted to determine the effect of varying the rivet diameter and pitch on the compressive strength of 24S-T aluminum-alloy panels with longitudinal Z-section stiffeners. The average stress at failing load for each rivet diameter, depth of countersink, and pitch of rivet is provided
Date: August 1945
Creator: Dow, Norris F. & Hickman, William A.
Partner: UNT Libraries Government Documents Department
open access

Tests of a Stressed-Carrying Door in Shear

Description: Bulletin presenting testing of a monocoque box with a stress-carrying door made and tested in torsion. The results indicate that if a stress-carrying door and its frame are made sufficiently heavy, the torsional stiffness of the box with the door can be made greater than the torsional stiffness of the box without the cut-out" (p. 1).
Date: August 1942
Creator: Gottlieb, Robert
Partner: UNT Libraries Government Documents Department
open access

Tests of a Stress-Carrying Door in Compression

Description: Bulletin presenting the results of bending tests on a monocoque box with the door on the compression side. The results indicate that the effectiveness of a stress-carrying door depends on the intended function of the door.
Date: September 1942
Creator: Gottlieb, Robert
Partner: UNT Libraries Government Documents Department
open access

Test Data on the Shear Strength of Machine Countersunk-Riveted Joints Assembled by an NACA Flush-Riveting Procedure

Description: Bulletin presenting load-displacement curves for use in establishing allowable-load values for riveted joints assembled by an NACA flush-riveting procedure. Comparative data are also given to show the effect of variations in the procedure on the yield and maximum shear loads for the rivets.
Date: December 1942
Creator: Gottlieb, Robert
Partner: UNT Libraries Government Documents Department
open access

Shear Tests on DuPont Explosive Rivets With the Countersunk Head Milled Flush After Expansion

Description: Report discusses the results of shear testing in which the heads of Du Pont explosive countersunk rivets were allowed to protrude above the skin surface before expansion and the protruding portions were removed after expansion. As the height of the rivet head above the skin increases, the tightness of the rivet was found to increase. The report concludes that it may be desirable to investigating filling an entire shank with an explosive charge in order to permit greater tolerances in the drille… more
Date: May 1943
Creator: Gottlieb, Robert & Bartone, Leonard M.
Partner: UNT Libraries Government Documents Department
open access

Comparative Tests of the Strength and Tightness of Commercial Flush Rivets of One Type and NACA Flush Rivets in Machine-Countersunk and Counterpunched Joints

Description: Report discusses an investigation that was conducted to compare the strength and tightness of machine-countersunk flush-riveted joints assembled with NACA flush rivets and a type of commercial flush rivet. A comparison was also generated between the strength and tightness of counterpunched flush-riveted joints assembled with the same types of rivet. NACA's flush-riveted joints tended to be stronger and tighter than the commercial joints.
Date: February 1, 1944
Creator: Mandel, Merven W.
Partner: UNT Libraries Government Documents Department
open access

A Study of the Tightness and Flushness of Machine-Countersunk Rivets for Aircraft

Description: Bulletin presenting the results of an investigation to determine possible improvements in the tightness and the flushness of machine-countersunk rivets. Specimens used in the study were simple lap joints made by different riveting methods. The results indicate that a comparison of the quality of machine-countersunk riveted joints on the basis of maximum load alone is not justified.
Date: June 1942
Creator: Lundquist, Eugene E. & Gottlieb, Robert
Partner: UNT Libraries Government Documents Department
open access

Tests of Hydraulically Expanded Rivets

Description: Report discusses the results of an investigation into the tightness, shear strength, tensile strength, and life under pulsating loads of hollow, hydraulically expanded rivets made of 17S-T aluminum alloy. The countersunk-head rivets with inserts had a much higher maximum load in shear than the modified-roundhead rivets, which did not have inserts.
Date: March 1944
Creator: Mandel, Merven W.; Crate, Harold & Schuette, Evan H.
Partner: UNT Libraries Government Documents Department
open access

Effect of Countersunk Depth on the Tightness of Two Types of Machine-Countersunk Rivet

Description: Bulletin presenting an investigation conducted to determine the effect of countersunk depth on the tightness of two types of machine-countersunk flush rivet. The specimens tested in the study were simple lap joints made by two different riveting methods. The results indicated that roundheaded rivets inserted from the back of the joint with the countersunk heads formed int he driving of the rivets produce tighter joints over a large range of depths than ordinary flush rivets.
Date: October 1942
Creator: Gottlieb, Robert
Partner: UNT Libraries Government Documents Department
open access

Proposal for a Propeller Side-Force Factor

Description: Report discusses a proposal for propeller manufacturers to consider the side-force factor with the activity factor as a fundamental parameter for all blade designs and for the side-force factor to be included in all reports of powered models in wind tunnels. The proposal includes a method for calculating the side-force factor and how it can be used in propeller development. It is shown to be a good index of the relative effectiveness per blade of a yawed propeller in developing side force.
Date: December 1943
Creator: Ribner, Herbert S.
Partner: UNT Libraries Government Documents Department
open access

The belt method for measuring pressure distribution

Description: "The measurement of pressure distribution may be accomplished rapidly for any number of locations deemed necessary in model or full-scale investigations by use of the 'belt' method. Reasonable accuracy may be obtained by careful use of this method" (p. 1).
Date: February 1943
Creator: Corson, Blake W., Jr.
Partner: UNT Libraries Government Documents Department
open access

End-zone water injection as a means of suppressing knock in a spark-ignition engine

Description: Report discusses the results of an investigation into the effectiveness of water injection into the combustion end zone of a spark-ignition engine cylinder for the suppression of knock. The injection angle was found to be very important for obtaining maximum results. The results of various angles and amounts of water were examined.
Date: September 1944
Creator: Brun, Rinaldo J.; Olsen, H. Lowell & Miller, Cearcy D.
Partner: UNT Libraries Government Documents Department
open access

Use of Internal Coolant as a Means of Permitting Increase in Engine Take-Off Power

Description: Engine tests, together with estimates made at Langley Memorial Aeronautical Laboratory, indicate that a 25-percent increase in take-off power can be obtained with present-day aircraft engines without increasing either the knock limit of the fuel or the external cooling requirements of the engine. This increase in power with present fuels and present external cooling is made possible through the use of an internal coolant inducted through the inlet manifold. Estimates on aircraft indicate that t… more
Date: January 1944
Creator: Rothrock, Addison M.
Partner: UNT Libraries Government Documents Department
open access

Calculations of Intake-Air Cooling Resulting From Water Injection and of Water Recovery From Exhaust Gas

Description: Report discussing some calculations made for the effects of water in cooling the inlet air of aircraft-engine cylinders. From Summary: "The estimates indicate that the cooling effect of the water on the inlet air can be more extensive than the cooling now obtained with the intercoolers or aftercoolers in the air-induction system. In connection with water recovery from the exhaust gas, the estimates indicate that sufficient water can be recovered from 50 percent of the exhaust gas to provide an … more
Date: August 1944
Creator: Rothrock, Addison M.
Partner: UNT Libraries Government Documents Department
open access

Cylinder-Head Cooling by Means of a Shield in the Exhaust Passage

Description: "Tests were run on a single-cylinder, air-cooled engine with a Wright C9GC cylinder to determine the improvement in cylinder-head cooling that can be obtained by building into the exhaust passage an insulating shield designed to protect the valve-guide boss and the exhaust-passage walls from the exhaust gas. The test results showed an appreciable improvement in cooling of the exhaust-valve-guide boss, of the guide bushing, and of the valve seat" (p. 1).
Date: June 1944
Creator: Wilsted, H. D. & Mulcahy, B. A.
Partner: UNT Libraries Government Documents Department
open access

Test Data on the Shear Strength of Joints Assembled With Round-Head and Brazier-Head Rivets

Description: Report discusses data obtained from testing shear of joints riveted with round-head and brazier-head rivets. The tightness of the rivets is also compared for one value of rivet diameter. The load-displacement curves and comparison of load at various values of permanent displacement are presented for both types of rivets.
Date: June 1943
Creator: Mandel, Merven W. & Schuette, Evan H.
Partner: UNT Libraries Government Documents Department
open access

A Positive-Replica Technique for Examining Finished Metal Surfaces and Its Application to Aircraft Engine Cylinders

Description: Report discusses a method of replica creation and testing of the surface-finish variation of aircraft engine parts subject to wear. In this report, a positive replica is created, the surface is treated, the replica is tested to make sure the fidelity is high enough, and a series of ring-sticking tests are conducted on the replicas. A summary of the results of the testing is also included.
Date: September 1944
Creator: Clark, Thomas P.
Partner: UNT Libraries Government Documents Department
open access

Method of Mounting Cylinder Blocks of in-Line Engines on CUE Crankcases

Description: Report describes the installation of six-cylinder blocks from two in-line aircraft engines on CUE crankcases, which permits the separate operation of any cylinder as part of a single-cylinder test engine. Using multicylinder-engine blocks for single-cylinder tests is advantageous because there is greater availability of standard engine parts and there is less temperature gradient. Modifications of the crankcase, camshaft-drive mechanism, and operation of the cylinder are described.
Date: July 1944
Creator: Waldron, C. D. & Biermann, A. E.
Partner: UNT Libraries Government Documents Department
open access

Effect of Inlet-Air Temperature and Cylinder Displacement on Charge Temperature of Internal Combustion Engines

Description: Report discussing the effect of inlet-air temperature and cylinder displacement on the charge temperature of an internal-combustion engine at the end of the induction stroke. The experiment to test various types of cylinders and their results on the air temperature and pressure is described.
Date: January 1944
Creator: Sanders, Newell D. & Bolz, Ray E.
Partner: UNT Libraries Government Documents Department
open access

Use of Water Injection to Decrease Gasoline Consumption in an Aircraft Engine Cruising at High Power

Description: Report discusses the results of testing water injection on a multicylinder aircraft engine and the potential fuel savings from the procedure. The speeds at which water injection for engine cooling is beneficial are illustrated and information about the manifold pressures and average rear spark-plug-gasket temperatures are also included.
Date: August 1944
Creator: Engelman, Helmuth W. & White, H. Jack
Partner: UNT Libraries Government Documents Department
open access

Comparative Fatigue Tests of Riveted Joints of Alclad 24S-T, Alclad 24S-T81, Alclad 24S-RT, Alclad 24S-T86 and Alclad 75S-T Sheet

Description: Report discusses testing performed to determine the fatigue strength of various types of riveted and spot-welded joints in the following aluminum alloys: Alclad 24S-T, 24S-RT, 758-T, 24S-T81, and 24S-T86. Details of the experiment, tensile properties, and information about failure are provided.
Date: August 1945
Creator: Moore, R. L. & Hill, H. N.
Partner: UNT Libraries Government Documents Department
open access

An Investigation of the Characteristics of a Propeller Alcohol Feed Ring

Description: Report discusses the results of an investigation to compare the discharge characteristics of an alcohol feed ring and a standard alcohol discharge nozzle when utilized to supply anti-icing alcohol to the propeller-blade feed shoes on a Curtiss-Wright C-46 cargo airplane. The equipment used, testing practices, and results of the alcohol flow distribution are described.
Date: June 1944
Creator: Neel, Carr B., Jr.
Partner: UNT Libraries Government Documents Department
Back to Top of Screen